What is ISUP and when should you use it?
ISUP (Intelligent Security Uplink Protocol) is a Hikvision protocol that allows an IP camera to be registered on a compatible recorder even when they are on different networks. The camera initiates the connection with the recorder, so there is no need to open ports at the camera location.
It is useful for centralizing cameras from different sites or installations with a 4G connection, such as a construction site or a ranch, on the same NVR. For example, a 4G camera located behind CG-NAT can connect to the office recorder, provided that it has Internet access and the recorder is accessible from the outside.
1. Check compatibility and prepare the network
- Hikvision recorder. It must support adding IP cameras through ISUP Service. For non-solar cameras, the Hikvision guide references NI-M and NXI-I (E) recorders with firmware V5.04.066 or later. Check the exact model's compatibility and confirm that the ISUP Service menu appears on the recorder. The appearance of ISUP under Platform Access does not confirm that it can receive cameras through this protocol.
- Hikvision camera. It must be compatible with ISUP 5.0 and have Internet access, either through a fixed network or 4G. On 4G models, check that the SIM card has data service and that the camera appears as connected to the mobile network.
- Recorder router. The recorder must be connected to the Internet through a router with a public IP address accessible from the outside. Preferably, use a static public IP address. If the public IP address is dynamic, you can use a DDNS domain that updates when it changes, provided that the camera supports a domain name in the ISUP server field and has its DNS configured. If the recorder's router is behind CG-NAT, a DDNS domain will not allow you to open the ports. In that case, request a public IP address from your provider.
- Recorder's local address. Assign the NVR a static IP address on the local network or a DHCP reservation so that the port-forwarding rules continue to point to the correct device.
2. Open the ISUP ports on the recorder's router
On the router at the installation where the NVR is located, go to Port Forwarding or Port Forwarding. Create one rule for each of the service's six ports, with the NVR's local IP address as the destination. For this configuration, use the same external and internal port number and select TCP and UDP, as shown in the Hikvision example.
| Default port | Function |
|---|---|
| 7660 | Camera registration with the ISUP service. |
| 7661 | Alarm reception. |
| 6011 | Reception of images associated with alarms. The Hikvision guide indicates that this cannot be modified on the referenced NVR. |
| 7662 | Live viewing. |
| 7663 | Playback of recordings. |
| 7664 | Two-way audio. |
Check that the ports match those shown under ISUP Service on the recorder. On the camera, only the registration port is entered, normally 7660. For this procedure, it is not necessary to open the web, RTSP, or SDK ports, or to open ports on the camera's router.
3. Configure the ISUP service on the recorder
- Go to Device Access → Device Configuration → Access Service → ISUP Service (Device Access → Device Configuration → Access Service → ISUP Service).
- Enable the service and confirm that the ports match the rules configured on the router.
- Set a strong ISUP encryption key. You will need to enter the same key on the camera. This is not the camera's or recorder's web access password.
- Enable Automatically Add IP Camera if you want the recorder to add the camera when it registers. If you prefer to add it manually, leave this option disabled.
- Select the transmission mode, Continuous or Scheduled, according to the installation. For the first test, you can select Continuous. Save the changes.
4. Configure ISUP on the camera
- Go to Configuration → Network → Platform Access → ISUP. Depending on the firmware, Platform Access may be under Advanced Settings.
- Enable ISUP, select ISUP 5.0, and configure these fields.
| Camera field | Value to enter |
|---|---|
| Server address | The public IP address of the recorder's router, or its DDNS domain if the camera supports it. Do not use the recorder's local IP address if the devices are on different networks. |
| Port | The external registration port. If you used the recommended mapping, enter 7660. |
| Device ID | A unique identifier for that camera. You can use its serial number. Do not repeat the ID on other cameras. |
| Encryption key | The same ISUP key configured on the recorder. |
3. Save the changes and check that the Registration Status changes to Online (Online).
5. Check the registration on the recorder
- Return to the NVR and go to Device Access → Video Device.
-
If you enabled automatic registration, check that the camera appears as Online, with the ISUP protocol and an assigned channel. If you did not enable automatic registration, click + Add, select ISUP, and enter the Device ID configured on the camera.
If the camera does not register, check its Internet access, the public IP address or domain, the 7660 port mapping, and that the ISUP key matches on both devices. If it registers but there is no image, first check the 7662 mapping and the selected transmission mode. If there is live video but you cannot find recordings, check the channel's recording schedule and the status of the NVR's disk.