The following scheme aims to streamline and better locate the options that are most relevant at any given moment.
JADE BIRD MENU | |||
| KEY | User level. 2, (111) | Installer menu. level 3 (1111 1111) | |
| F1 | REVIEW MENU | 1. View event history | 1. All events 2. Alarms 3. Faults 4. Operator actions 5. Input/Output |
| 2. View faults | |||
| 3. View canceled | |||
| 4. View zones in test | |||
| 5. View zone status | |||
| 6. View device status | |||
| 7. View loop address descriptions | |||
| 8. Serial number | |||
| 9. View system components and configuration date | |||
| 0. Maintenance contact information | |||
| KEY | User level. 2, (111) | Installer menu. level 3 (1111 1111) | |
| F2 | OPERATE | 1. Zone test | |
| 2. Output group test 3. Keyboard test | |||
| 4. Indicator test | |||
| 5. Bypass/Enable zone | |||
| 6. Bypass/Enable outputs | |||
| 7. Bypass/Enable device | |||
| 8. Adjust date/time | |||
| KEY | User level. 2, (111) | Installer menu. level 3 (1111 1111) | |
| F3 | REPORTS | 1. Print event history | |
| 2. Device report. Type and status | |||
| 3. View serial numbers and software versions | |||
| 4. Loop response signal report | |||
| 5. View full device response | |||
| 6. Device signal strength | |||
| 7. View advanced programming | |||
| 8. View addresses assigned to a zone | |||
| 0. View addresses used in a loop |
| KEY | User level. 2, (111) | Installer menu. level 3 (1111 1111) | |
| F4 | SETTINGS | 1. Manually add or remove loop devices | |
| 2. Enter device text | |||
| 3. Assign devices to zones | |||
| 4. Delays and cause-effect of SND / FR by zone | 1. Configure SND/FR delays for all zones 2. Configure siren delay by zone 3. Configure FR output delay by zone 4. Link/unlink sirens by zone 5. Link/unlink FR outputs by zone | ||
| 5. Configure loop class A or B | |||
| 6. Assign output or siren to output group | |||
| 7. Maintenance contact information | |||
| 8. View analog graph of a detector | |||
| 9. Configure day/night mode | |||
| 0. Configure printer |
| KEY | User level. 2, (111) | Installer menu. level 3 (1111 1111) | |
| F5 | INSTALLATION | 1. Step-by-step assistant | 1. Installation assistant 2. Maintenance assistant |
| 2. Auto-register devices | |||
| 3. Configure password | 1. Operator password 2. Installer password | ||
| 4. Language | 1. EN (English) 2. SP (Spanish) 3. CA (Catalan) 4. PT (Portuguese) | ||
| 5. Special operation mode | 1. JBE-P2L1 EN 54 2. Commissioning | ||
| 6. Enter advanced programming | |||
| 7. Delete configurations and factory values | 1. Delete device text 2. Delete zone configuration 3. Delete advanced programming 4. Load factory settings | ||
| 8. System composition |
Configuration / Update via USB
This feature allows loading a complete fire panel configuration from a USB file. Users can also update the panel firmware using a USB memory device.
To enable this menu, insert the memory into the USB port and press the SW1 button located next to it. The USB port is located on the inside face of the panel door.
Attention
- Before using this feature, format the USB memory with the FAT32 format.
- Use a blank memory unit: Do not mix panel files with files for other uses on the USB memory.
- Remember to use a USB version 2 (connector interior black color); memories larger than 8GB are not recommended.
- The USB menu options are as follows:
1. Save event log to USB
2. Save entire configuration to USB
3. Load configuration from USB
4. Software update from USB